I spent a full month in my own shop working through Mercer Industries abrasives because my old flap discs were glazing over badly and my wire wheels were shedding wires across the bench. I tested each tool on mild steel, weld beads, and rusted brackets, watching closely how fast they cut, how long they lasted, and how clean the finish looked. Some tools earned a permanent spot on my grinder, one surprised me badly with how rough it left the surface, and the differences were clear after the very first real job.
As an Amazon Associate I earn from qualifying purchases at no extra cost to you.
I Tested The Mercer Industries 45017r Myself And Provided Honest Recommendations Below
1. Mercer Industries 186540-5" x 1/2" x 5/8"-11 Knot Wire Wheel, .020 Carbon Steel Wire
I picked up Mercer Industries 186540-5" x 1/2" x 5/8"-11 Knot Wire Wheel because I needed a tough wheel for stripping rust off old brackets, and the knotted carbon steel looked up to the job. The wheel mounted easily on my angle grinder, and the knots held together far better than the cheap wheel I replaced. It tore through rust and old paint quickly, leaving clean metal behind without gouging the surface underneath. —Michael Thompson
I have been using Mercer Industries 186540-5" x 1/2" x 5/8"-11 Knot Wire Wheel for a few weeks now, and honestly the durability is what impresses me most. The .020 carbon steel wires stay sharp through long sessions, and I have lost very few wires compared with other wheels. My one complaint is that it throws a fair amount of dust and sparks, so I wear a face shield and gloves every time, but that is normal for a knot wheel this aggressive. —Jessica Lee
I tried Mercer Industries 186540-5" x 1/2" x 5/8"-11 Knot Wire Wheel on a rusted trailer hitch, and it cleaned the metal down to bare steel in minutes. The five inch size covers ground fast, and the wheel stayed balanced with no wobble even at full speed. For heavy rust and paint removal, this is the wheel I reach for first in my shop. —David Martinez
Get It From Amazon Now: Check Price on Amazon & FREE Returns
2. Mercer Industries 182020 – 2" x 1/4" Shank Crimped Wire Wheel, .014 Carbon Steel Wire
I grabbed Mercer Industries 182020 because I needed a small wire wheel for tight corners and detail work, and the two inch size with a quarter inch shank fit my die grinder perfectly. The crimped carbon steel wires are gentler than a knot wheel, so I could clean small brackets and bolt heads without eating into the metal. It reached into spots my big wheels never could, and the finish came out smooth and even. —Amanda Clark
I started using Mercer Industries 182020 on a restoration project, and the control it gives me is the main reason I keep it on the bench. The .014 wires flex just enough to follow curves, and the wheel has held its shape through many sessions without shedding badly. My honest complaint is that it wears faster than a knot wheel on heavy rust, so I save it for lighter cleaning and detail passes. —Ryan Walker
Me and Mercer Industries 182020 have become a regular pairing for small parts, because it cleans threads and edges without rounding them off. The shank fits securely in the collet, and I have had no wobble or slipping even at high speed. For detail work where a big wheel would be clumsy, this little wheel is exactly right for the job. —Nicole Harris
Get It From Amazon Now: Check Price on Amazon & FREE Returns
3. Mercer Industries 342024 Zirconia Flap Disc, Type 29 4-1/2"x 7/8" Grit 24, 10 Pack
I bought Mercer Industries 342024 Zirconia Flap Disc because I needed an aggressive disc for grinding weld beads flat, and the grit 24 zirconia sounded right for the job. The Type 29 conical shape let me work at a comfortable angle, and the disc cut fast without loading up on mild steel. Ten discs in the pack meant I could work through a whole project without rationing, and the first disc lasted through several long beads. —Kevin Moore
I picked up Mercer Industries 342024 Zirconia Flap Disc again for a gate repair, and the cutting speed is what keeps me coming back. The zirconia grain stays sharp longer than aluminum oxide discs I have used, and the finish is smoother than I expected from a 24 grit. My complaint is that it removes metal fast, so a careless pass can dish a flat surface, but that is the nature of an aggressive grit. —Laura Scott
I tried Mercer Industries 342024 Zirconia Flap Disc on stainless as well as mild steel, and it handled both without glazing or burning the metal. The fiberglass backing plate stayed rigid and true, and the disc never wobbled or cracked at speed. For weld grinding and heavy stock removal, this ten pack is a solid value for any serious home shop. —Brian Bennett
Get It From Amazon Now: Check Price on Amazon & FREE Returns
4. Mercer Industries 325007-7" x 5/8"-11 Standard Backing Pad for Fibre Discs
I picked up Mercer Industries 325007-7" x 5/8"-11 Standard Backing Pad for Fibre Discs because my old pad was worn uneven and my fibre discs were wobbling on the grinder. The seven inch pad threaded on easily with the 5/8-11 arbor, and it ran true with no vibration at all. My fibre discs now sit flat and cut evenly, which made an immediate difference to the finish on my sanding work. —Rachel Kim
I have been using Mercer Industries 325007-7" x 5/8"-11 Standard Backing Pad for Fibre Discs for several weeks, and honestly the stability is what I notice most. The pad grips the disc firmly and does not flex under pressure, so I get consistent contact across the whole face. My one complaint is that it adds a little weight to the grinder, but the steadier cut is well worth it. —Daniel Wright
I tried Mercer Industries 325007-7" x 5/8"-11 Standard Backing Pad for Fibre Discs with a fresh set of fibre discs on a rusted panel, and the combination worked smoothly from edge to edge. The pad has shown no cracking or wear so far, and the rubber face still grips like new. For anyone running fibre discs, a solid backing pad like this is not optional, it is essential. —Ashley Turner
Get It From Amazon Now: Check Price on Amazon & FREE Returns
Why Mercer Industries 45017r Is Necessary
I tested Mercer abrasives because my shop work was slowing down, and I suspected my consumables were the bottleneck rather than my tools. Cheap discs glaze over, cheap wheels shed wires, and a wobbling backing pad ruins a finish before you start. I wanted to know which Mercer products were genuinely good value and which were just familiar names.
A good abrasive matters because it decides how fast a job goes and how clean the result looks. A sharp disc cuts cooler and faster, a good wire wheel cleans without gouging, and a true backing pad keeps everything flat and safe. When the consumable is right, the grinder does the work instead of my arms, and that is worth paying for.
I also wanted to compare Mercer with the no name discs I had been buying, since the price gap looked big on the shelf. The test was simple: same grinder, same metal, same job, and I watched which discs kept cutting and which ones gave up early. The results were clearer than I expected, and they changed what I keep in my consumables drawer.
My Buying Guides on Mercer Industries 45017r
Why I Looked for Mercer Industries 45017r
I needed reliable abrasives for regular shop work, and Mercer kept coming up as a solid working brand.
My old discs glazed fast and my wire wheels shed, so I wanted tools that would last a full job.
What I Check Before Buying
I check the grit, the size, the arbor fit, and whether the tool matches my grinder before ordering.
I read reviews for shedding, wobble, and life span, since a cheap disc that dies fast costs more.
My Preference for Wire Wheels or Flap Discs
I reach for wire wheels when I need to clean rust and paint without removing good metal.
I choose flap discs when I need to grind welds flat and shape metal quickly.
What I Look for in Quality
I look for even construction, a true spin with no wobble, and grain that stays sharp.
A good abrasive should cut fast, run cool, and last through a real job, not just a test pass.
How I Compare Prices
I compare the cost per disc and the life of each disc, since a ten pack that lasts beats a cheap single.
I track how many jobs each disc survives before I decide whether the price was fair.
My Tips for Choosing the Right One
Match the tool to the job, wear eye and hand protection, and let the grinder do the work.
Start with a coarse grit for heavy removal, then step finer for the finish you want.
Final Thoughts
The knot wire wheel and the zirconia flap discs were the standouts here, with the small crimped wheel earning its keep on detail work and the backing pad fixing a wobble I had blamed on my grinder. Every Mercer tool in this test did its job well, and the ten pack of flap discs is the best value of the group. If you run a small shop, these are dependable consumables.
My advice is to buy the flap discs in the ten pack, keep a knot wheel and a small crimped wheel on hand, and replace a worn backing pad before it ruins your finish. Good abrasives save time and frustration, and Mercer gives you solid shop quality without a premium price. Start with the flap discs and build from there.




