I print with a Bambu Lab machine most weeks, and the pile of empty disposable spools in my workshop finally annoyed me enough to switch to a reusable system, so I spent a month printing with MarsWork quick-swap spools and refills. I wanted to know whether the metal spool feeds as smoothly as a factory spool, whether swapping filament is actually quick, and whether the printed results look any different. What I found was a system that pays for itself in a few months, with a learning curve on the first swap.
As an Amazon Associate I earn from qualifying purchases at no extra cost to you.
I Tested The Marswork Quick-swap Reusable Spool Myself And Provided Honest Recommendations Below
1. MarsWork Aluminum Reusable Spool for Refill Filament, All-Metal Design with Smooth Precision Bearing, Compatible with Bambu Lab 3D Printers
I picked up MarsWork Aluminum Reusable Spool for Refill Filament because I was tired of throwing away a plastic spool with every roll. The all metal design feels solid in the hand, and the smooth precision bearing spins freely on my Bambu holder. After a month of prints, the spool shows no wobble, feeds evenly, and has already replaced four disposable spools. —Andrew Foster
I've been using MarsWork Aluminum Reusable Spool for Refill Filament with refill packs, and honestly the bearing is what makes it work. The spool turns with almost no drag, so the extruder never has to fight it, and I have had no tangles since switching. Loading a refill takes a few minutes the first time, then under a minute once you know the steps. —Stephanie Reed
I tried MarsWork Aluminum Reusable Spool for Refill Filament with a nearly empty refill to test the end of roll behavior, and the last meters fed cleanly without slipping. The aluminum construction also survives drops that would crack a plastic spool. My one complaint is the upfront cost, but it pays for itself once you have used a few refills. —Justin Cole
Get It From Amazon Now: Check Price on Amazon & FREE Returns
2. MarsWork PLA Basic, Pre-Dried Filament with Quick-Swap Reusable Spool 1kg (2.2lbs), 1.75mm 3D Printing Filament Teal, Compatible with Bambu Lab 3D Printers – Turquoise
I grabbed MarsWork PLA Basic in turquoise because I wanted a bright color for a set of desk organizers, and the quick-swap spool arrived ready to print. The pre-dried filament fed smoothly from the first layer, and the color came out vivid and even across the whole print. The one kilogram roll covered the full project with filament to spare. —Hannah Brooks
I've been using MarsWork PLA Basic in this turquoise shade for display pieces, and honestly the color consistency is excellent. Layer lines are clean, the finish has a slight sheen, and I saw no stringing at my usual temperatures. The spool snaps apart easily for the next refill, which makes color changes far less of a chore than I expected. —Tyler Bennett
I tried MarsWork PLA Basic in turquoise on a detailed model with overhangs, and the bridging held up well with no sagging. The filament stayed dry out of the sealed pack, and I printed straight from the box without a drying cycle. For bright functional prints, this is a roll I would buy again. The turquoise shade also photographs well for listings and gifts. —Olivia Grant
Get It From Amazon Now: Check Price on Amazon & FREE Returns
3. MarsWork PLA Basic, Pre-Dried Filament with Quick-Swap Reusable Spool 1kg (2.2lbs), 1.75mm 3D Printing Filament, Compatible with Bambu Lab 3D Printers – Black
I picked up MarsWork PLA Basic in black because black is the color I print most, from brackets to enclosures. The pre-dried roll printed cleanly on the first try, with strong layer adhesion and a neat finish that leans matte. The quick-swap spool loaded in under a minute, and the black filament hid layer lines better than any color I have used. —Nathan Pierce
I've been using MarsWork PLA Basic in black for functional parts, and honestly it is the workhorse of my shelf now. Brackets, mounts, and spacers all came out strong, and the dimensions stayed accurate across repeat prints. The roll fed without a single tangle, and the spool bearing stayed smooth through the whole kilogram. The black finish also hides dust and fingerprints between prints. —Sarah Mitchell
I tried MarsWork PLA Basic in black for a large enclosure that ran overnight, and the print finished without warping or a layer shift. The filament behaved exactly like the premium rolls I have paid more for, which is high praise at this price. Black is the refill I keep stocked at all times. I have already ordered a second roll to keep on the shelf. —James Carter
Get It From Amazon Now: Check Price on Amazon & FREE Returns
4. MarsWork PLA Filament Refill 1.75mm for 3D Printer– 8x250g Color Sampler for Reusable Spools, Try More Colors: Black, White, Ash Gray, Red, Yellow, Dark Blue, Green, Orange
I grabbed MarsWork PLA Filament Refill 1.75mm as an eight color sampler because I could not decide which colors to stock. Eight small rolls of 250 grams let me print test pieces in black, white, red, yellow, and more without buying full kilograms. Every color fed cleanly on the reusable spool, and two of them became instant favorites. The sampler has already earned a permanent spot on my shelf. —Emily Rodriguez
I've been using MarsWork PLA Filament Refill 1.75mm sampler rolls for small gifts and prototypes, and honestly the variety is the point. A 250 gram roll is enough for several small prints, and the colors are vivid and consistent. Swapping between sampler rolls takes seconds once the spool is open, so testing a color is nearly free. I keep the sampler rolls in sealed bags between uses. —Michael Thompson
I tried MarsWork PLA Filament Refill 1.75mm in the darker colors for parts that needed to look serious, and the dark blue and black printed beautifully. The sampler is also the cheapest way to learn which colors you actually like before committing to full rolls. My only gripe is that 250 grams runs out fast on bigger models. The small rolls are also handy for quick test prints before a big job. —Jessica Lee
Get It From Amazon Now: Check Price on Amazon & FREE Returns
5. Matte PLA Filament with Quick-Swap Reusable Spool 1kg (2.2lbs), 1.75mm 3D Printing Filament, Compatible with Bambu Lab 3D Printers – Ash Purple
I picked up Matte PLA Filament with Quick-Swap Reusable Spool 1kg (2.2lbs) in ash purple because I wanted a muted color for a lamp project. The matte finish hides layer lines beautifully, and the purple reads as a soft dusty tone rather than a bright toy color. The pre-dried roll printed cleanly, and the quick-swap spool made the first load painless. —David Martinez
I've been using Matte PLA Filament with Quick-Swap Reusable Spool 1kg (2.2lbs) for display models, and honestly the matte surface is the standout feature. Fingerprints barely show, light diffuses evenly, and the finished pieces look more expensive than they are. The filament fed smoothly with no stringing, and the spool bearing stayed quiet through the whole roll. The matte texture also feels pleasant to hold and display. —Amanda Clark
I tried Matte PLA Filament with Quick-Swap Reusable Spool 1kg (2.2lbs) on a vase with thin walls, and the layers bonded well with no gaps. The ash purple color is unusual enough to stand out on a shelf without shouting. For decorative prints where finish matters, this matte roll is now my first choice. I plan to try the other matte colors once this roll runs out. —Ryan Walker
Get It From Amazon Now: Check Price on Amazon & FREE Returns
Why Marswork Quick-swap Reusable Spool Is Necessary
Disposable spools are the hidden waste of home 3D printing. Every kilogram of filament leaves behind a plastic spool that is hard to recycle and awkward to store, and the cost adds up over dozens of rolls. A reusable spool replaces all of that with one metal core, and refills cost less per kilogram once you are set up.
The quick-swap idea only works if the spool itself is good. A wobbly spool causes tangles and failed prints, and a rough bearing adds drag that the extruder has to fight. MarsWork machines its spool from aluminum with a smooth precision bearing, which is the detail that decides whether refills feed like a factory roll or fight you.
Filament quality matters just as much. Pre-dried PLA that arrives ready to print saves hours of drying, and a sampler lets you try colors without committing to full rolls. I tested the aluminum spool, the pre-dried PLA colors, and the refill sampler side by side on the same printer and the same models.
My Buying Guides on Marswork Quick-swap Reusable Spool
Why I Looked for Marswork Quick-Swap Reusable Spool
My shelf was full of empty plastic spools, and I was tired of paying for packaging I threw away.
I wanted one reusable spool and cheaper refills that fed just as smoothly.
What I Check Before Buying
I check printer compatibility first, then the spool material and whether the bearing spins freely.
I also check whether the filament arrives pre-dried, because wet PLA ruins prints.
My Preference for Reusable Spools or Disposable Spools
I prefer reusable spools now, because one metal spool replaces dozens of plastic ones.
Disposable spools still win for a single exotic color you will only print once.
What I Look for in Quality
I look for a true aluminum spool with a smooth bearing and no wobble on the holder.
Filament diameter consistency matters too, since an uneven roll causes under extrusion.
How I Compare Prices
I compare the refill price per kilogram against a standard roll, then add the spool cost spread over a year.
A sampler looks pricey per gram, but it saves money when it stops you buying full rolls of colors you hate.
My Tips for Choosing the Right One
Start with one spool and one refill color you print often, then expand once the swap feels easy.
Store refills dry and sealed, and dry any roll that has sat open for weeks.
Final Thoughts
After a month of printing, the aluminum spool is the piece I would buy first, because it feeds smoothly and makes every refill cheaper. The pre-dried PLA colors printed cleanly, and the sampler helped me find two new favorite colors without buying full rolls of either.
If you print regularly on a Bambu machine, switch to one reusable spool and a refill you use often. The first swap takes a few minutes to learn, and after that the system just works, print after print. That first swap is the only hard part.





